Injection mould, 3D printing or vacuum casting: which is right for 200 to 1 lakh parts a year?
Short answer: Under about 10 parts, 3D print. For 10 to 200, 3D printing or vacuum casting works. From about 200 parts, a fast tool-steel mould usually wins: real moulded parts in your own plastic, at production piece price, in about 15 days. Above about 1 lakh parts a year, build a full production mould.
The right process depends mostly on how many parts you need. Material, finish and timing matter too, but quantity decides first.
Which route is best for your quantity?
| Parts you need | Best route | Why |
|---|---|---|
| 1–10 | 3D printing | No mould cost at all. Fine for a look-and-feel sample. |
| 10–200 | 3D printing or vacuum casting | Look-alike parts in resin, low upfront cost. |
| 200 – 1 lakh a year | Fast tool-steel mould (Express Mould) | Real moulded parts in your own plastic, production piece price, about 15 days. On a shared base, about 4,000–5,000 pieces a month; if you need more, the same inserts move to a dedicated base with no monthly limit. |
| Over 1 lakh a year | Full production mould | Multi-cavity tooling gives the lowest cost per piece. |
What does each route really cost?
Upfront cost. 3D printing has none. Vacuum casting needs a silicone mould, which is cheap. A fast mould costs about half of a conventional mould, because the steel base is reused and only the core and cavity are made for your part. A full production mould costs the most.
Cost per piece. This is where the picture flips. Printed and cast parts stay expensive on every single piece. Moulded parts cost about the same as mass production from the first run.
Time to first parts. 3D printing: 1–3 days. Vacuum casting: about 7–10 days. Express Mould: mould ready in 15 days, moulded parts in 15–17 days. Conventional mould: around 45 days, often more.
Material and finish. Printed parts show layer lines and are rarely your final material. Cast parts are a resin that imitates it. Moulded parts are your actual plastic, injection moulded, with the same strength and finish as mass production. That matters for drop tests, snap fits, certification and anything a customer will hold.
What is the most common mistake?
Many teams keep 3D printing or vacuum casting long after it stops making sense, often for 500 or 5,000 parts, because a mould sounds slow and expensive. The result is prototype prices for production parts, and a material that is not the real one.
A useful rule: if you will need more than a couple of hundred identical parts, price a mould before you print another batch.
When is a fast mould not the answer?
Be honest with yourself here. A fast mould on a standard base fits about 8 in 10 parts. It is the wrong choice for:
- very complex parts with many sliders, lifters or side actions;
- parts too large for a 300 ton machine base;
- more than about 1 lakh parts a year, where a multi-cavity production mould is cheaper per piece.
How can you decide in 5 minutes?
- Write down how many parts you need in the next 12 months.
- Check whether the part must be in the final plastic (strength, certification, customer-facing).
- If the answer is "more than 200" and "yes", ask for a mould quote alongside your next print or casting quote, and compare the total cost, not just the first invoice.
Questions buyers ask
Is a mould worth it for only 500 parts?
Often, yes. 3D printing or vacuum casting 500 parts means paying prototype prices 500 times, in a look-alike material. A fast mould costs more upfront, but each part then costs about the same as mass production and is made in your real plastic.
How many parts can a vacuum-casting silicone mould make?
Typically around 20 to 25 parts before the silicone mould has to be remade, and the parts are in a polyurethane resin that imitates the final plastic.
When should I skip Express Mould and go straight to a production mould?
When you need more than about 1 lakh parts a year, need several cavities, or the part is very complex, with many sliders or side actions. A full production mould is cheaper per piece at that volume.