Home / Videos · Mould Ka Sach
Mould Ka Sach: the injection mould comedy series
Short answer: Mould Ka Sach is a short Hinglish comedy series by General Plastic Industries (GPI) about the injection mould and tool room world. Each episode plays out a situation every mould buyer will recognise, then Amit Verma, Head of Tool Room at GPI, explains the real reason and what to ask for next time. New episodes every week on YouTube and Instagram.
- 15 days
- to a ready tool-steel mould
- ~50%
- lower die cost
- ₹2,000/day
- we pay if we are late
- Since 1968
- General Plastic Industries, Delhi
The die maker quotes ₹5 lakh, the buyer bargains it to ₹3 lakh. When a mould is under-quoted, the saving usually comes from the steel. Lesson: ask for the steel test certificate before you order.
A mould promised in 40 days takes 120, because the die maker took more orders than the tool room could handle. Lesson: get a written milestone plan, weekly photo updates and a penalty clause for delays.
The samples look perfect, but they were filed, sanded and touched up overnight, and production parts don't match. Lesson: ask for off-tool samples, straight from the mould with no hand finishing, and attend the trial.
A 1 mm change after the steel is cut turns into a big bill. Lesson: check fit and assembly with a prototype or RPT and freeze the design before you order the die.
Trial after trial, a new defect each time, because there was no DFM or mould flow analysis before the steel was cut. Lesson: ask for the mould flow report and the mould design, and have an expert check them.
Every mould buyer has lived these stories
Most first-time mould buyers learn the same lessons the hard way: the cheapest quote that costs more, the "40 days" that becomes 120, the sample that looked perfect, and the trial that never ends. Mould Ka Sach turns those moments into short comedy episodes, then gives the real, technical answer in under a minute.
What you learn in each episode
- Ep 1, the cheap mould: when a die maker under-quotes, the saving usually comes from the steel. Ask for the steel test certificate. Read the guide.
- Ep 2, the 40-day promise: delays usually come from a tool room that has taken more work than it can handle. Ask for a written milestone plan, weekly photo updates and a penalty clause. Read the guide.
- Ep 4, the perfect sample: samples can be hand-fixed overnight. Ask for off-tool samples and attend the trial.
- Ep 5, the 1 mm change: changes after steel cutting get expensive. Check the design with a prototype or RPT before you order the die.
- Ep 6, the endless trials: trial after trial often means no DFM and no mould flow analysis. Ask for the mould flow report and mould design, and get them checked.
Watch and share
Follow on YouTube and Instagram for a new episode every week. Share it with your purchase team, or with the friend who always takes the cheapest quote.
Need a mould done right?
Express Mould by General Plastic Industries builds a tool-steel injection mould in 15 days from design approval, at about half the usual cost. If we are late, we pay ₹2,000 a day. Send your drawing for a review.
Questions buyers ask
What is Mould Ka Sach?
A short comedy series in Hindi and Hinglish about getting an injection mould made: cheap quotes, delays, 'bas ek trial aur', and the real reasons behind them. Each episode ends with a correct, practical fix from GPI's Head of Tool Room, Amit Verma.
Who is it for?
Anyone who works with moulds: product founders and purchase teams buying a mould, mould makers and tool room staff, moulding operators, and plastic engineering and CIPET students.
Where can I watch new episodes?
On YouTube at @mouldkasachgpi and on Instagram at @mouldkasach. New episodes come out every week.
Can GPI make my mould?
Yes. Through Express Mould, GPI builds a tool-steel injection mould in 15 days from design approval, at about half the usual cost, or pays ₹2,000 a day if late. Send your part or drawing for a review.